plantgeorge0

Fiat 500 Replacement Key Fob If your 500 remote key fob isn't functioning, it could be time to replace the battery. If you replace the battery, but it's still not working it could be a problem elsewhere. At United Locksmith, we specialize in the creation of new keys for old cars. We have the tools and parts needed for this job. Dead Coin Battery The most frequent reason that your Fiat 500 key fob will not lock or unlock the doors is a dead battery. The key fob has the battery of a coin-cell that is prone to draining quickly in the event that it is not frequented enough. If your remote began to show signs of weakness such as a loss in range and stopped working completely the battery could be dead. Metal clips keep the battery in place within the key fob. If the clips are loose, it could lead to problems with contact, which can prevent the remote from receiving power. Use a flathead screwdriver to remove the retaining clip and remove the old battery. Make fiat ducato replacement key The Keylab to select an identical replacement battery type of voltage, dimensions, and specification as the original battery. The key fob could also become corroded or damaged due to exposure to water. Even a quick bath in soapy water could damage the electronic chip inside. Make sure your key fob is dry. Water Damage Damage to your water supply could be the reason for your key fob's not functioning properly. Key fobs are fitted with rubber seals that prevent them from being damaged by rain or a splash of water, but it is crucial to keep your car keys safe from the ocean, pool, and washing machine! The key fob is equipped with an electronic chip which sends a message to the immobilizer of your car. This is what allows your 500 to lock or start, but if the chip gets wet, it's unable to longer function. If you're trying to determine if your key fob is still functioning it is possible to clean the internal electronics with isopropyl or electronic cleaner. However, it is probably best to get a replacement from a dealer instead of trying to repair the key fob that has been submerged in salt water. While a replacement fob might cost a bit of money, it is a lot cheaper than paying for your Fiat 500 to be towed to the dealer for repair! Plus, you can make it yourself in just only a few steps. Be sure to have the correct type of battery prior to opening your keyfob. You can find step-by-step instructions for any car keyfob on the internet. Faulty Chip The chip located within the key fob communicates to your car's immobiliser system to ensure the vehicle is only capable of starting when the correct key is used. If the chip is damaged or damaged in any way it will not start. A damaged chip could occur due to several reasons, but most often it is due to water damage or an unresponsive battery. It is best to delegate the task to a professional locksmith who can repair the chip quickly and at an affordable price. If your key fob will not work after exposure to clean rain or tap water take it off the battery. Clean the electronic component using paper towels. If the key fob does not work, there's the possibility that it has an issue with the component and requires to be replaced. Some people will go to their dealer when in need of an entirely new Fiat key fob, however this could be a expensive option. If you are looking for a cost-effective way to have your Fiat key fob repaired Look no further than United Locksmith. We have the tools and knowledge required to repair your Fiat key fob in a quick and professional way. Faulty Receiver Module Fiat key fobs send an electrical signal to the vehicle, which will unlock and close doors (and start the vehicle for those with an automatic transmission) up to 50 feet. However there are several things that can cause the fob to stop working. This includes a dead coin battery water damage buttons, worn ones and a receiver module issue and signal interference or an electronic chip that has failed. If the fob was stored in a place that has experienced extreme trauma, like being dropped on a hard floor or being washed in the washing machine, it may not be capable of communicating with the car's Body Control Module (BCM). This is because the BCM is an extremely secure system that will only accept signals from a genuine original key and not accept any other. You'll need to replace the fob in case this happens. A professional locksmith will take care of the entire process of replacing your key including programming a new key to your 500. They can even provide an clone fob that performs just like the original (and costs a fraction of the cost).